6KW Water Cooling Microwave Accessories Magnetron 6000W Microwave Variable Frequency Magnetron For Microwave Parts
| Application |
Industrial microwave heating, drying, sterilization equipment,UV environmental protection equipment, micro magnetic equipment |
| ebm |
7.30kV |
| Po(1) |
6000W |
| Cooling mode |
Water Cooling |
| Frequency |
2455MHz |
| Ef |
1.5 V |
| Power Supply |
DC power supplywith the less than 2% of power ripple rate |
| Max Output |
6000W |
| Filament current |
20A |
Please feel free to contact us with any questions. We have professional engineers on staff, ready to address your questions or concerns.
For 6kW MAGNETRON
6000W Microwave Variable Frequency Magnetron
1. HandlingBecause the filament is made of thoriated-tungsten wire and carbonized, it is quite weak against vibration and shock. Please be careful about the handling. Vibration resonant frequency of this filament is 300~400Hz. Please avoid to provide vibration in this frequency range. High Voltage is provided on the magnetron. Please don't touch when it is operating. Ensure unplug the cable during servicing. Microwave leakage from magnetron input (filament terminal) is prevented by filter circuit.
However leakage from output shall be pay attention to confirm electrical contact of magnetron gasket and wave-guide lip. The protection for the secondly circuit short should be installed. Please prevent to operate in the environment with dust, moisture or corrosive gas. Please prevent to provide excessive force to the terminals of the feed-through capacitor
Outline Drawing(2M343H)Unit:mm
1500W Microwave Variable Frequency Magnetron
1.This specifications is applied for CW magnetron model PM60AL-03PLN
2. RoHSThis magnetron complies with RoHS 2 (Directive 2011/65/EU).
3. Operation warrantyIt requires the proper usage, which is within absolute maximum ratings and technical note.We warrants the initial defects under the condition above.
1500W Microwave Variable Frequency Magnetron
Note
1. The tube shall be mounted on the output coupler (Fig. 6) or similar one.Ambient Temperature :25CCooling: Approximately 4.0L/min (Water Cooling)Power Supply:DC power supplywith the less than 2% of power ripple rate
2. Filament voltage should be regulated as shown in Fig. 1 and the value should be adjusted for each type of the power supply.
3. The point for measuring anode/Tp and filter case/Tc temperature are shown in the outline drawing.
4. The temperature of the feed-through capacitor shall be below 120C.
5. Measurement shall be done within 60 seconds after anode voltage supplied.Temperature correction is calculated as follows; ebm (T) = [1 - 0.0008 (T - 25)] ebm
Po (T)= [1 - 0.0008 (T - 25)] Po
T: Ambient Temperature [°C] ebm (T) : Peak Anode Voltage at T°C[KV]
Po (T) : Average Output Power (1) at T°C [W]
6. No continuous spark occur.
7.Test Classification
Design Test
Production Test
1500W Microwave Variable Frequency Magnetron
For 1.5kW MAGNETRON 2M343 SERIES Air-cooled
2. Connection of Filament Terminals Filament current is over 20 A. Contact defect causes huge voltage drop and it makes serious operation failures. Inside of filter case becomes high temperature. Please provide air cooling of 400L/min or more from outside. The water cooling of tube and the air cooling of filter case are necessary during preheat.
1500W Microwave Variable Frequency Magnetron
Matched Load Condition (VSWR 1.1) ebm:7.30 kV
Po(1)i:6000 W f:2455 MHz
Measurement Condition
Power Supply :DC power supply with the less than 2% of power ripple rate
Reference Plane:Antenna Center
Ef Operation :1.5 V
Ib:1100 mAdc
3. Preheating and Cut BackMore than 120 seconds preheating of filament is required before applying high voltage for reliable operation and longer life. When applying high voltage, filament voltage should be regulated as shown in Fig. 1 during the operation and the value should be adjusted for each type of the power supply.
4. Load ImpedancePlease design the load impedance does not exceed the absolute maximum rating any time for reliable operation and longer life. It is recommended to use an isolator unit. Operation exceeding the absolute maximum rating causes abnormalities such as antenna and anode temperature rise, antenna spark, moding, filament melting, and runaway, which would cause a failure.
5. Recommendation of Waveguide DesignSame dimensions as R.F. Coupler [Fig.6] are recommended. Embossed edge shall be flat and the contact resistance shall be low.
Company Profile
Zhuhai PindomTechnology Co., Ltd.
Zhuhai PindomTechnology Co., Ltd.is a high-tech enterprise focusing on the development of solid-state microwave and radio frequency technology, and adhering to the corporate philosophy of technology to change lives, create value for customers, and bring convenience to the society, and provide families and enterprises with solid-state microwaves. It is committed to becoming a high-tech enterprise with social influence on household, commercial and industrial-grade smart products of radio frequency technology.
Certifications
Packaging & Shipping
Supply Ability:500 Piece/Pieces per Month
Packaging Details:The industrial microwave custom equipment is packed in wooden cases with iron hoops.
Port:Shenzhen China
Lead Time:
| Quantity(pieces) |
1 - 50 |
>50 |
| Est. Time(days) |
15 |
To be negotiated |
FAQ
1. Why should you buy from us instead of another supplier?
We are a professional and innovative team. With independent research and development and production capacity, quality and service first, abide by the spirit of business and contract.
2. How can we guarantee the quality?
Our products are subject to strict testing at every stage from production, packaging to pre-shipment.
3. Payment
1. Terms of payment: telegraphic transfer, letter of credit, credit card, etc. Please contact us for details.
2. Please fill in the complete information, contact person, address, ZIP code and phone number when placing an order to ensure the smooth delivery of your goods.
4. Shipping
1. After confirming the payment, we will deliver the goods within 2~5 working days.
2. We will provide the best transportation company and transportation route for you to choose.
5. Quotation
1. Generally, the quotation will be completed within 1 working day.
2. For complex customized products or products requiring mold opening, we may need more time to calculate the cost and then give you a quotation.
6. After-sale service and warranty
1. The warranty period of our products is 3 months to 2 years. The warranty time start calculating upon customers receiving the goods.
2. We provide paid repair service for artificially damaged products and fragile accessories.
3. Any quality issues please feel free to contact us. We are dedicated to solve the problem for you.
7. The feedback
1. As your feedback is very important to our business development, we sincerely invite you to give the feedback.
2. We will deal with your feedback in time, and you can also keep in touch with our customer service and get the updated progress.
6KW Water Cooling Microwave Accessories Magnetron 6000W Microwave Variable Frequency Magnetron For Microwave Parts
Audited Supplier 
){kind=link}